Yamaha XVS13AW Service Manual Download Page 285

Page: 285 / 422

CRANKSHAFT

5-79

5. Measure:

• Crankshaft journal diameter “a”

Out of specification

→

Replace the crank-

shaft.

NOTE:

Measure the diameter of each crankshaft journal
at two places.

6. Measure:

• Crankshaft journal bearing inside diameter

“a”
Out of specification

→

Replace the crank-

case assembly.

NOTE:

Measure the inside diameter of each crankshaft
journal bearing at two places.

7. Calculate:

• Crankshaft-journal-to-crankshaft-journal-

bearing clearance
Out of specification

→

Replace the crank-

shaft and crankcase as a set.

NOTE:

Calculate the clearance by subtracting the
crankshaft journal diameter from the crankshaft
journal bearing inside diameter.

EAS26150

INSTALLING THE CONNECTING RODS

1. Lubricate:

• Bolt threads

(with the recommended lubricant)

2. Lubricate:

• Crankshaft pin
• Big end bearings
• Connecting rod inner surface

(with the recommended lubricant)

3. Install:

• Big end bearings
• Connecting rods
• Connecting rod caps

(onto the crankshaft pin)

NOTE:

• Align the projections “a” on the big end bear-

ings with the notches “b” in the connecting rods
and connecting rod caps.

• Be sure to reinstall each big end bearing in its

original place.

• Make sure the projection “c” on each connect-

ing rod faces towards the left side of the crank-
shaft.

• Make sure the characters “d” on both the con-

necting rod and connecting rod cap are
aligned.

Crankshaft journal diameter

49.968–49.980 mm (1.9672–
1.9677 in)

Crankshaft journal bearing inside
diameter

50.010–50.030 mm (1.9689–
1.9697 in)

Crankshaft-journal-to-crankshaft-
journal-bearing clearance

0.030–0.060 mm (0.0012–0.0024
in)

Recommended lubricant

Molybdenum disulfide grease

Recommended lubricant

Engine oil

Summary of Contents for XVS13AW







































































































































































































































































































































































































































Search results

Summary of Contents for XVS13AW

Reviews:

Related manuals for XVS13AW

Brands by name

Popular brands

Yamaha XVS13AW, Service Manual

Search results

Summary of Contents for XVS13AW

Reviews:

Related manuals for XVS13AW

Brands by name

Popular brands