Yamaha XVS13AW(C), Service Manual

Page: 78 / 422

CABLE ROUTING
2-52
1. Left handlebar switch lead
2. Clutch cable
3. Front brake hose
4. Meter assembly lead
5. Sidestand switch coupler
6. Oil level switch coupler
7. Radiator fan motor coupler
8. Front cylinder intake air pressure sensor
9. Coolant temperature sensor coupler
10. Rear cylinder intake air pressure sensor
11. Left handlebar switch couplers
12. Rear cylinder ignition coil
13. Sub-wire harness couplers
14. Front cylinder ignition coil
15. Rear cylinder thermostat inlet hose
16. Front cylinder thermostat inlet hose
17. Oil level switch
18. Starter motor lead
19. Radiator fan motor lead
20. Front cylinder spark plug cap
21. Front cylinder spark plug lead
22. Wire harness
23. Fuel tank
24. Coolant reservoir hose
25. Right handlebar switch lead
26. Oil level switch lead
27. Sidestand switch lead
A. Route the meter assembly lead under the left
handlebar switch lead and clutch cable.
B. Fasten the left handlebar switch lead and front
cylinder spark plug lead with a plastic locking tie.
Be sure to install the plastic locking tie on the left
handlebar switch lead’s protective sleeve and
position it 10
–
15 mm (0.39
–
0.59 in) from the end
of the sleeve. Face the end of the plastic locking tie
inward, and then cut off the excess end of the tie.
C. Black connectors
D. White connectors
E. Connect the ignition coil leads with the “I” marks to
the front cylinder ignition coil. Route the ignition
coil lead with the black terminal to the outside of
the wire harness.
F. Route the sub-wire harness to the inside of the fuel
pipe in the area shown in the illustration.
G. To engine
H. Route the front cylinder spark plug lead to the
outside of the rear cylinder spark plug lead.
I. Fasten the sidestand switch lead, starter motor
lead, and oil level switch lead with plastic locking
ties. Face the end of each plastic locking tie
downward, and then cut off the excess end of the
tie.
J. The starter motor lead, neutral switch lead, and
sidestand switch lead may be routed in any order
in the area shown in the illustration.
K. Fasten the starter motor lead at the positioning
tape to the engine mounting boss with a plastic
locking tie. Position the buckle of the plastic locking
tie in front of the boss, with the end facing upward,
and then cut off the excess end of the tie to 15 mm
(0.59 in) or less.
L. Fasten the starter motor lead and sidestand switch
lead with a plastic locking tie. Face the end of the
plastic locking tie rearward, and then cut off the
excess end of the tie.
M. Fasten the sidestand switch lead and oil level
switch lead with the holder. Face the fastener of the
holder outward.
N. Route the radiator fan motor lead to the front of the
fuel tank breather hose and fuel tank overflow
hose.
O. Fasten the sidestand switch lead, oil level switch
lead, and radiator fan motor lead with the holder.
Face the fastener of the holder outward.
P. Route the sidestand switch lead, radiator fan motor
lead, and oil level switch lead to the front of the
radiator inlet hose.
Q. Fasten the sidestand switch lead to the frame with
a plastic locking tie. The oil level switch lead and
radiator fan motor lead may also be fastened with
the plastic locking tie. Face the end of the plastic
locking tie rearward, making sure that it does not
contact the left side panel.
R. Fasten the sidestand switch lead, oil level switch
lead, and radiator fan motor lead with the plastic
band. Face the end of the plastic band rearward.
Do not install the plastic band on the couplers or
the sections of the leads that are not covered by
the protective sleeves.
S. Cut off the excess end of the plastic locking tie and
position the cut end within the area shown in the
illustration.
T. Fasten the leads (to sub-wire harness) that branch
off from the wire harness below the frame weld.
U. Fasten the sidestand switch lead, oil level switch
lead, and radiator fan motor lead with a plastic
locking tie. The leads may be fastened in any
order.