Yamaha WaveRunner VX Cruiser 2007 Page 93 Owner'S/Operator'S Manual Download

Page: 93 / 96

Trouble recovery

plers get wet, they could corrode, which
could lead to poor connections.

(5) Crank the engine for 5 seconds at wide

open throttle. Repeat this step until all of
the water in the cylinders has been ex-
pelled.

(6) Spray a rust inhibitor into each spark plug

hole for 5 seconds.

(7) Crank the engine for 5 seconds at wide

open throttle. Repeat this step several
times.

(8) Install the spark plugs, and then connect

the spark plug caps and fuel injector cou-
plers.

CAUTION:

ECJ00780

Do not start the engine even after complet-
ing the previous steps. Any water remain-
ing in the engine could cause serious
engine damage.

(9) Have the watercraft inspected by a

Yamaha dealer as soon as possible.

CAUTION:

ECJ00790

Be sure to have a Yamaha dealer inspect
the watercraft. Otherwise, serious engine
damage could result.

UF1K72E0.book Page 86 Wednesday, August 2, 2006 10:43 AM

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands

Yamaha WaveRunner VX Cruiser 2007, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands