Yamaha WaveRunner VX Cruiser 2007 Owner'S/Operator'S Manual Download

Page: 33 / 96

Features and functions

EJU31020

Operation of controls and other

functions

EJU31031

Seat

There is a seat latch at the rear of the seat to
remove the seat.
To remove the seat:
Pull the seat latch up, and then pull the seat
off.

VX/VX Deluxe

VX Cruiser

To install the seat:
Insert the projection on the front of the seat
into the stay on the deck, and then push the

rear of the seat down to lock it in place secure-
ly.

NOTE:

Make sure that the seat is securely installed
before operating the watercraft.

EJU31071

Hood

To open the hood, pull the hood latch up, and
then lift up the hood.

Seat latch

Hood latch

UF1K72E0.book Page 26 Wednesday, August 2, 2006 10:43 AM

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands

Yamaha WaveRunner VX Cruiser 2007, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands