Yamaha WaveRunner VX Cruiser 2007 Owner'S/Operator'S Manual Download

Page: 49 / 96

Operation

EJU31890

Engine oil

Use a combination of the recommended SAE
and API engine oil classifications shown in the
chart below.

CAUTION:

ECJ00280

Use only 4-stroke engine oil.

EJU31930

Filling the fuel tank

CAUTION:

ECJ00290

Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.

(1) Remove the seat. (See page 26 for seat

removal and installation procedures.)

(2) Remove the fuel tank filler cap, and then

slowly add fuel to the fuel tank. Stop filling
when the fuel level reaches approximate-

ly 50 mm (2 in) from the top of the fuel
tank as indicated in the illustration.

(3) Install the fuel tank filler cap and the seat.

Approximately 50 mm (2 in) from top of the
fuel tank

Fuel tank capacity:

60 L (15.9 US gal) (13.2 Imp.gal)

UF1K72E0.book Page 42 Wednesday, August 2, 2006 10:43 AM

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands

Yamaha WaveRunner VX Cruiser 2007, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX Cruiser 2007

Reviews:

Related manuals for WaveRunner VX Cruiser 2007

Brands by name

Popular brands