manualshive.com logo in svg

Yamaha WaveRunner VX Cruiser 2007, Owner'S/Operator'S Manual

Share
Download
Yamaha WaveRunner VX Cruiser 2007 Owner'S/Operator'S Manual Download Page 9

General and important labels

2

EJU36110

Model information (for Europe 

only) 

EJU30330

Builder’s plate 

Part of the information is given on the builder’s
plate affixed on the craft. A full explanation of
this information is given in the relevant sec-
tions of this manual.

Design category of this personal water-
craft: C
Category C:

This watercraft is designed to operate in
winds up to Beaufort force 6 and the associat-
ed wave heights (significant wave heights up
to 2 m (6.56 ft); see the following NOTE).
Such conditions may be encountered in ex-
posed inland waters, in estuaries, and in
coastal waters in moderate weather condi-
tions.

NOTE:

The significant wave height is the mean
height of the highest one-third of the waves,
which approximately corresponds to the wave
height estimated by an experienced observer.
However, some waves will be double this
height.

1

Builder’s plate location

UF1K72E0.book  Page 2  Wednesday, August 2, 2006  10:43 AM

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands