background image

Operation

60

(6) Gradually increase the speed to balance

the watercraft.

EJU33230

Capsized watercraft 

If the watercraft capsizes, turn it over immedi-
ately.
Be sure to carefully follow the procedures be-
low to prevent injury, or damage to the water-
craft.

WARNING

EWJ00670

IMPROPER UPRIGHTING CAN CAUSE IN-
JURY:

Be sure to shut the engine off by pulling
on the engine shut-off cord to remove
the clip from the engine shut-off switch.

Do not put your hands in the intake
grate.

CAUTION:

ECJ00530

If the watercraft capsizes, release the
throttle lever immediately. Oil could flow
into the air filter case and the engine could
be damaged.

(1) Remove the clip from the engine shut-off

switch.

(2) Swim to the rear of the watercraft. Pull the

watercraft over with your left hand on the

ride plate while pushing down on the gun-
wale with your right hand or foot.

NOTE:

If the port (left) side of the capsized watercraft
is tilting up, push down on the gunwale so that
the port (left) side is down before turning the
watercraft clockwise.

CAUTION:

ECJ00540

Do not turn the watercraft over counter-
clockwise, otherwise water can enter the
engine, which can result in severe dam-
age.

(3) Start the engine and operate the water-

craft to discharge any water remaining in
the engine compartment. (If the engine
does not start, see “Towing the water-
craft” on page 85 or “Submerged water-
craft” on page 85.)

UF1K72E0.book  Page 60  Wednesday, August 2, 2006  10:43 AM

Summary of Contents for WaveRunner VX Cruiser 2007

































































































Reviews: