manualshive.com logo in svg

Yamaha VZ150D, Owner'S Manual

Share
Download
Yamaha VZ150D Owner'S Manual Download Page 57

 

Maintenance

 

52

 

EMU29050

 

Checking water in engine oil tank

 

Oil injection models

 

There is a water trap at the bottom of the en-
gine oil tank. If water or foreign matter is vis-
ible in this trap, consult your Yamaha dealer.

 

EMU29111

 

Checking wiring and connectors

 

●

 

Check that each grounding wire is properly
secured.

 

●

 

Check that each connector is engaged se-
curely.

 

EMU29120

 

Exhaust leakage

 

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

 

EMU29130

 

Water leakage

 

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

 

EMU29153

 

Checking power trim and tilt system

WARNING

 

EWM00430 

 

●

 

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

 

●

 

Make sure no one is under the outboard

 

motor before performing this test.

 

1.

Check the power trim and tilt unit for any
sign of oil leaks.

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

3.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

 

1. Water trap
2. Engine oil tank

2

1

ZMU01895

ZMU04007

 

1. Tilt rod
2. Trim rods

ZMU03458

1

2

Summary of Contents for VZ150D


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands