Yamaha VZ150D Owner'S Manual Download | Manualshive

Page: 44 / 81

background image

Operation

39

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28184

Procedure for power trim and tilt / power
tilt models

1.

Place the gear shift lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

3.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 41.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

UP

ZMU01935

UP

DN

UP

ZMU04000

«
...
42
43
44
45
46
...
»

Summary of Contents for VZ150D


















































































Reviews:

No comments

Related manuals for VZ150D

Brand: MotorGuide Pages: 21

PIC18F57Q84 Curiosity Nano

Brand: Microchip Technology Pages: 39

Brand: EPOX Pages: 83

Brand: AOpen Pages: 8

Brand: FAAC Pages: 8

Brand: Texas Instruments Pages: 38

Brand: Icop Pages: 40

MEG X570S UNIFY-X MAX

Brand: MSI Pages: 204

Brand: Quick Pages: 48

Brand: Commell Pages: 53

Brand: Texas Instruments Pages: 20

Brand: Supermicro Pages: 1

STEVAL-LLL002V1

Brand: STMicroelectronics Pages: 29

Super 7 SY-5SSM

Brand: SOYO Pages: 86

Brand: JETWAY Pages: 60

Brand: Renesas Pages: 6

Brand: Gigabyte Pages: 86

Brand: Freescale Semiconductor Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands