manualshive.com logo in svg

Yamaha VZ150D, Owner'S Manual

Share
Download
Yamaha VZ150D Owner'S Manual Download Page 22

 

Basic components

 

17

 

EMU26391

 

Top cowling lock levers

 

To remove the outboard motor top cowling,
pull up the front and rear lock levers. Then lift
off the cowling. When the cowling, check to
be sure it fits properly in the rubber seal.
Then lock the cowling again by moving the
levers downward.

CAUTION:

 

ECM00550 

 

The air intake grille on the top cowling is
not designed as a handle and could break

 

if used as such.

 

EMU26460

 

Flushing device

 

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

 

For details on usage, see page 44.

 

EMU26470

 

Tachometer

 

This gauge shows the engine speed and has
the following functions.

 

1. Tilt support lever

1. Top cowling lock lever(s)

ZMU03979

1

ZMU03986

1

 

1. Air intake grille
2. Top cowling lock lever(s)

1. Flushing device

1

1

ZMU04787

2

2

1

ZMU04011

Summary of Contents for VZ150D


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands