Yamaha VZ150D Owner'S Manual Download Page 51

Page: 51 / 81

Maintenance

EMU28521

Maintenance chart

Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines. Refer to the sections in this chapter for
explanations of each owner-specific action.
The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

months)

100

hours (6
months)

200

hours (1

year)

Anode(s) (external)

Inspection / replace-
ment

Anode(s) (internal)

Inspection / replace-
ment

Battery

Inspection / charging

Cooling water pas-
sages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be dis-
assembled)

Inspection / replace-
ment

Fuel system

Inspection

Gear oil

Change

Greasing points

Greasing

Idling speed (EFI mod-
els)

Inspection / adjustment

PCV (Pressure Con-
trol Valve)

Inspection

Power trim and tilt unit

Inspection

Propeller and cotter pin

Inspection / replace-
ment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Throttle link / throttle
cable / throttle pick-up
timing

Inspection / adjustment

Throttle position sen-
sor

Inspection / adjustment

Water pump

Inspection

High pressure fuel
pump drive belt

Inspection / replace-
ment

Summary of Contents for VZ150D


















































































Search results

Summary of Contents for VZ150D

Reviews:

Brands by name

Popular brands

Yamaha VZ150D, Owner'S Manual

Search results

Summary of Contents for VZ150D

Reviews:

Brands by name

Popular brands