Yamaha VZ150D Owner'S Manual Download | Manualshive

Page: 33 / 81

background image

Operation

28

when starting or during operation.

●

Keep hands, hair, and clothes away
from the flywheel and other rotating

parts while the engine is running.

2.

Watch for oil flowing through the oil feed
pipes. After any air in the oil lines has
been expelled, the oil injection system
should supply oil normally. If no oil is
flowing after 10 minutes of idling, consult
your Yamaha dealer.

CAUTION:

ECM00560

●

Be sure to take the above steps when
operating the engine after a long period
of storage. Otherwise engine seizure
could occur.

●

Use straight gasoline only. If premix
fuel is used, the fuel injector could be

damaged.

EMU27233

Filling fuel and engine oil

EMU30320

Filling fuel for models without a fuel
joint

WARNING

EWM00060

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other

sources of ignition.

1.

Remove the fuel tank cap.

2.

Carefully fill the fuel tank.

3.

Securely close the cap after filling the
tank. Wipe up any spilled fuel.

EMU27270

Ring Free Fuel Additive

Gasoline is a precise blend of many different
substances, each chosen to give certain
characteristics. Gasoline blends have been
changing in recent years in response to con-
cerns about pollution and resulting emis-

ZMU03988

ZMU03989

«
...
31
32
33
34
35
...
»

Summary of Contents for VZ150D


















































































Reviews:

No comments

Related manuals for VZ150D

Brand: Acer Pages: 15

Brand: Acer Pages: 12

Brand: Hailo Pages: 22

Brand: AXIOMTEK Pages: 2

Brand: Linear Technology Pages: 6

GA-MA785GMT-UD2H

Brand: Gigabyte Pages: 104

Brand: ISSC Pages: 39

Brand: TYAN Pages: 96

Brand: Supermicro Pages: 229

Brand: Advantech Pages: 66

Super 7 SY-5SSM

Brand: SOYO Pages: 86

Brand: Supermicro Pages: 119

XtremeDSP Spartan-3A DSP 3400A...

Brand: Xilinx Pages: 50

CT-PBT01 Series

Brand: C&T Solution Pages: 48

Brand: Mercury Pages: 42

Brand: Icop Pages: 41

Brand: Maxim Pages: 33

Brand: Aaeon Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands