background image

–35–

FUEL PUMP SYSTEM

ELEC

5. Fuel pump relay

Disconnect the relay unit from the coupler.

Connect the pocket tester (

 

 1) and battery

(12 V) to the relay unit ferminals as shown.

Battery positive terminal 

 red / black 

Battery negative terminal 

 blue / red 

Tester positive probe 

 red / black 

Tester negative probe 

 blue / black 

1

1

2

3

Does the fuel pump relay have continuity be-
tween red / black and blue / black?

YES

NO

Replace the relay unit

6. Fuel pump resistance

Disconnect the fuel pump coupler from the
wire harness.

Connect the pocket tester (

 

 1) to the fuel

pump coupler (fuel pump side) as shown.

1

2

EB808400

Tester positive probe 

 black / blue 

Tester negative probe 

 black 

YES

NO

Relpace the fuel pump.

Measure the fuel pump resistance.

Fuel pump resistance

 10 

 at 20

C

Is the fuel pump OK?

7. Wiring

Check the entire fuel pump system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the fuel pump system’s wiring properly con-
nected and without defects?

EB808401

YES

NO

Prperly connect or re-
pair the fuel pump
system’s wiring.

Replace the ignitor
unit.

Summary of Contents for TDM850'99 4TX-AE3












































Reviews: