background image

NOTE:

CAUTION:

EB001000

NOTICE

This manual was produced by the Yamaha Motor Company primarily for use by Yamaha dealers and their
qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manual, so it is
assumed that anyone who uses this book to perform maintenance and repairs on Yamaha motorcycles has
a basic understanding of the mechanical ideas and the procedures of motorcycles repair. Repairs at-
tempted by anyone without this knowledge are likely to render the motorcycles unsafe and unfit for use.

Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and significant
changes in specifications or procedures will be forwarded to all authorized Yamaha dealers and will appear
in future editions of this manual where applicable.

Designs and specifications are subject to change without notice.

IMPORTANT INFORMATION

Particularly important information is distinguished in this manual by the following notations.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY
IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to the
motorcycle operator, a bystander or a person inspecting or repairing the  motor-
cycle.

A CAUTION indicates special precautions that must be taken to avoid damage to
the motorcycle.

NOTE:

A NOTE provides key information to make procedures easier or clearer.

Summary of Contents for TDM850'99 4TX-AE3












































Reviews: