Yamaha T-50 Owner'S Manual Download Page 75

Page: 75 / 116

Operation

2. After stopping the engine, disconnect

the fuel hose from the fuel joint on the
outboard motor by turning it counter-
clockwise.

3. Install the fuel joint cap on the outboard

motor.

4. Disconnect the fuel hose from the fuel

joint on the fuel tank by turning it coun-
terclockwise.

5. Tighten the air vent screw by turning it

clockwise.

6. Remove the key if the boat will be left un-

attended.

TIP:

The engine can also be stopped by pulling
the cord and removing the clip from the en-
gine shut-off switch, then turning the main
switch to “

” (off).

1. Fuel joint
2. Fuel hose

1. Fuel joint cap

ZMU07458

ZMU07459

1. Fuel joint
2. Fuel hose

1. Air vent screw

ZMU07443

ZMU07444

6C1-9-3B-1E0.book 69 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

Summary of Contents for T-50





















































































































Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands

Yamaha T-50, Owner'S Manual

Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands