Yamaha T-50 Owner'S Manual Download Page 104

Page: 104 / 116

Trouble Recovery

Q. Is fuel joint connection incorrect?
A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29433

Temporary action in

emergency

EMU29441

Impact damage

WARNING

EWM00870

The outboard motor can be seriously
damaged by a collision while operating or

trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1. Stop the engine immediately.
2. Check the control system and all compo-

nents for damage. Also, check the boat
for damage.

3. Whether damage is found or not, return

to the nearest harbor slowly and careful-
ly.

4. Have a Yamaha dealer check the out-

board motor before operating it again.

EMU30683

Replacing fuse

If a fuse has blown, open the fuse holder and
remove the fuse with a fuse puller. Replace
it with a spare one of the proper amperage.

WARNING

EWM00631

Substituting an incorrect fuse or a piece
of wire could allow excessive current
flow. This could cause electric system
damage and a fire hazard.

Consult your Yamaha dealer if the new fuse
immediately blows again.

6C1-9-3B-1E0.book 98 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

Summary of Contents for T-50





















































































































Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands

Yamaha T-50, Owner'S Manual

Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands