Yamaha T-50 Owner'S Manual Download Page 68

Page: 68 / 116

Operation

4. Align the groove in the fuel joint on the

outboard motor with the protrusions on
the fuel hose.

5. Push in the fuel hose and turn it clock-

wise to connect it securely.

6. Align the groove in the fuel joint on the

fuel tank with the protrusions on the fuel

hose.

7. Push in the fuel hose and turn it clock-

wise to connect it securely.

8. Wipe up any spilled gasoline immediate-

ly with dry rags.

TIP:

Dispose of rags properly according to local
laws or regulations.
9. When using the fuel tank on the boat, a

3. Primer pump
4. Toward the fuel tank

1. Fuel joint
2. Groove
3. Protrusion
4. Fuel hose

1. Fuel hose

ZMU07453

ZMU07454

1. Fuel joint
2. Groove
3. Protrusion
4. Fuel hose

1. Fuel hose

ZMU07455

ZMU07456

6C1-9-3B-1E0.book 62 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

Summary of Contents for T-50





















































































































Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands

Yamaha T-50, Owner'S Manual

Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands