Yamaha T-50 Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 116

background image

Specifications and requirements

19

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an
alternative oil grade listed under Recom-
mended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36360

Fuel requirements

EMU41331

Gasoline

Use a good quality gasoline that meets the
minimum octane requirement. If knocking or
pinging occurs, use a different brand of gas-
oline or premium unleaded fuel. Yamaha
recommends that you use alcohol-free gaso-
line (see Gasoline with Ethanol) whenever
possible.
The use of a poor quality gasoline may result
in starting and running problems. If you en-
counter drivability problems, which you sus-
pect could be related to the fuel you are
using, we recommend that you switch to a
recognized high quality brand of gasoline,
such as a gasoline that is advertised as Top
Tier Detergent Gasoline. Failure to comply
with these recommendations may also result
in unscheduled maintenance, fuel system
damage, and internal engine damage.

NOTICE

ECM01981



Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.



Avoid getting water and contaminants
in the fuel tank. Contaminated fuel can
cause poor performance or engine
damage. Use only fresh gasoline that
has been stored in clean containers.

Gasoline with Ethanol

Two types of gasoline are commonly avail-
able in the U.S.A. and Canada for use in au-
tomobiles and boats: conventional gasoline

Recommended engine oil:

YAMALUBE 4M FC-W or 4-stroke out-
board motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL

Engine oil quantity (without oil filter re-
placement):

1.9 L (2.01 US qt, 1.67 Imp.qt)

Engine oil quantity (with oil filter replace-
ment):

2.1 L (2.22 US qt, 1.85 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

Recommended fuel:

Regular unleaded gasoline

Min. pump octane number (PON):

86

6C1-9-3B-1E0.book 19 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

«
...
23
24
25
26
27
...
»

Summary of Contents for T-50





















































































































Reviews:

No comments

Related manuals for T-50

Brand: LABTEC Pages: 12

Brand: Ultimate Sound Pages: 7

Brand: Bazooka Pages: 10

Brand: Akai Pages: 21

Wireless2100-System

Brand: MultiChannel Pages: 43

Brand: Altinex Pages: 10

Brand: Texas Instruments Pages: 25

Brand: XTA Pages: 14

Acoustic Box II

Brand: Vintage Revolution Pages: 17

Brand: Marantz Pages: 27

Brand: YOKOGAWA Pages: 4

1783 SIGNAL PROCESSING

Brand: Altec Lansing Pages: 9

3W Amplified Phone Neckloop

Brand: Spy Earpice Pages: 3

Brand: ALLNIC AUDIO Pages: 6

Brand: ELECRAFT Pages: 55

Brand: Omron Pages: 2

Brand: Fishman Pages: 16

Brand: Parasound Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands