Yamaha T-50 Owner'S Manual Download Page 56

Page: 56 / 116

Engine control system

EMU26803

Alert system

NOTICE

ECM00091

Do not continue to operate the engine if a
alert device has activated. Consult your
Yamaha dealer if the problem cannot be
located and corrected.

EMU2681C

Overheat alert

This engine has an overheat-alert device. If
the engine temperature rises too high, the
alert device will activate.



The engine speed will automatically de-
crease to about 2000 r/min.



The overheat-alert indicator will light or
blink.



The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the alert system has activated, stop the en-
gine and check the cooling water inlets:



Check trim angle to be sure that the cool-
ing water inlet is submerged.



Check the cooling water inlet for clogging.

ZMU05028

ZMU07103

6C1-9-3B-1E0.book 50 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

Summary of Contents for T-50





















































































































Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands

Yamaha T-50, Owner'S Manual

Search results

Summary of Contents for T-50

Reviews:

Related manuals for T-50

Brands by name

Popular brands