Yamaha STRATOLINER XV19CTSV Owner'S Manual Download Page 33

Page: 33 / 100

INSTRUMENT AND CONTROL FUNCTIONS

3-16

WARNING

EWA14320

Be careful not push the motorcycle
forward when removing the wind-
shield. The motorcycle could fall off
the sidestand.

CAUTION:

ECA15350

Securely hold the windshield to pre-
vent it from falling when removing.

To install the windshield

1. Fit the slot in each windshield

bracket (left and right side) into its
holder.

WARNING

EWA14300

Make sure that the throttle cables
are not pinched.

2. Push the windshield backward un-

til it snaps into place.

3. Insert the key into the windshield

lock, turn it counterclockwise until
it stops to lock the fastener, and
then remove the key.

WARNING

EWA14270

Make sure that the fastener is locked
in place as shown.

1. Slot

2. Holder

3. Throttle cable

1. Lock.
2. Fastener

3. Holder

U2C510E0.book Page 16 Monday, September 12, 2005 1:17 PM

Summary of Contents for STRATOLINER XV19CTSV





































































































Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands

Yamaha STRATOLINER XV19CTSV, Owner'S Manual

Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands