Yamaha STRATOLINER XV19CTSV Owner'S Manual Download Page 45 | Manualshive

Page: 45 / 100

background image

OPERATION AND IMPORTANT RIDING POINTS

5-2

5

CAUTION:

ECA11130

For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

NOTE:

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

CAUTION:

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16680

To start out and accelerate

1. Pull the clutch lever to disengage

the clutch.

2. Shift the transmission into first

gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at

the same time, release the clutch
lever slowly.

1. Shift pedal

2. Neutral position

U2C510E0.book Page 2 Monday, September 12, 2005 1:17 PM

«
...
43
44
45
46
47
...
»

Summary of Contents for STRATOLINER XV19CTSV





































































































Reviews:

No comments

Related manuals for STRATOLINER XV19CTSV

Brand: LAZER Pages: 13

Brand: Memphis Shades Pages: 2

Brand: AGV Pages: 45

2006 G 650 Xmoto

Brand: BMW Pages: 132

HPS.08.473.10000/B

Brand: SW-Motech Pages: 4

Brand: N-Com Pages: 32

XV17ATMV(C) Road Star

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 118

Super Tenere ES 2022

Brand: Yamaha Pages: 132

Brand: Yamaha Pages: 282

Super Tenere ES 2020

Brand: Yamaha Pages: 130

Brand: Yamaha Pages: 211

Sixteenth Edition

Brand: MSF Pages: 60

Brand: Vanucci Pages: 35

Brand: Yamaha Pages: 5

1985 XV700 Virago

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands