Yamaha STRATOLINER XV19CTSV Owner'S Manual Download Page 78

Page: 78 / 100

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

EAU24180

Tail/brake light

This model is equipped with an LED
type of tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

EAU38380

Replacing a turn signal light
bulb

1. Remove the turn signal light lens

by removing the screw, and then
turning the lens counterclockwise.

2. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by turning it clock-

wise, and then installing the screw.

CAUTION:

ECA11190

Do not overtighten the screw, other-
wise the lens may break.

EAU24330

License plate light

If the license plate light does not come
on, have a Yamaha dealer check the
electrical circuit or replace the bulb.

1. Screw

U2C510E0.book Page 31 Monday, September 12, 2005 1:17 PM

Summary of Contents for STRATOLINER XV19CTSV





































































































Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands

Yamaha STRATOLINER XV19CTSV, Owner'S Manual

Search results

Summary of Contents for STRATOLINER XV19CTSV

Reviews:

Related manuals for STRATOLINER XV19CTSV

Brands by name

Popular brands