Yamaha Star XV19MY Owner'S Manual Download | Manualshive

Page: 61 / 94

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

7

EAU22751

Changing the brake and
clutch fluids

Have a Yamaha dealer change the
brake and clutch fluids at the intervals
specified in the TIP after the periodic
maintenance and lubrication chart. In
addition, have the oil seals of the brake
and clutch master cylinders and cali-
pers as well as the brake and clutch
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

●

Oil seals: Replace every two
years.

●

Brake and clutch hoses: Replace
every four years.

EAU23040

Drive belt slack

The drive belt slack should be checked
and adjusted at the intervals specified
in the periodic maintenance and lubri-
cation chart.

EAU38410

To check the drive belt slack

1. Place the vehicle on the sidestand.
2. Note the current position of the

drive belt using the marks near the
drive belt check hole.

TIP

The marks near the drive belt check
hole are 5.0 mm (0.2 in) apart.

3. Note the position of the drive belt

with a force of 45 N (4.5 kgf, 10 lbf)
applied to the belt with a belt ten-
sion gauge as shown.

TIP

A belt tension gauge is available at a
Yamaha dealer.

4. Calculate the drive belt slack by

subtracting the measurement not-
ed in step 2 from the measurement
noted in step 3.

5. If the drive belt slack is incorrect,

have a Yamaha dealer adjust it.

1. Drive belt
2. Marks

3. Drive belt slack

1. Belt tension gauge

Drive belt slack:

7.5–13.0 mm (0.30–0.51 in)

U1D713E0.book Page 19 Thursday, May 8, 2008 4:19 PM

«
...
59
60
61
62
63
...
»

Summary of Contents for Star XV19MY































































































Reviews:

No comments

Related manuals for Star XV19MY

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: R&G Pages: 12

Brand: Memphis Shades Pages: 2

Brand: Miller Pages: 12

Easyrack 6612533 01 01

Brand: hepco & becker Pages: 5

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 216

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands