Yamaha Star XV19MY Owner'S Manual Download | Manualshive

Page: 18 / 94

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-2

4

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “

”

and “

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11363

Fuel level warning light “

”

This warning light comes on when the
fuel level drops below approximately
3.0 L (0.79 US gal, 0.66 Imp.gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, and then go off,
have a Yamaha dealer check the elec-
trical circuit.

TIP

This model is also equipped with a self-
diagnosis device for the fuel level de-
tection circuit. If a problem is detected
in the fuel level detection circuit, the fol-
lowing cycle will be repeated until the
malfunction is corrected: The fuel level
warning light will flash eight times, and

1. Push.
2. Turn.

1. Neutral indicator light “

”

2. High beam indicator light “

”

3. Right turn signal indicator light “

”

4. Left turn signal indicator light “

”

5. Engine trouble warning light “

”

6. Fuel level warning light “

”

U1D713E0.book Page 2 Thursday, May 8, 2008 4:19 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for Star XV19MY































































































Reviews:

No comments

Related manuals for Star XV19MY

Brand: Öhlins Pages: 2

Brand: SRC Pages: 5

Brand: GLOBBER Pages: 72

TRIUMPH Bonneville T 120

Brand: hepco & becker Pages: 4

Brand: Dakota Digital Pages: 7

Brand: METRAKIT Pages: 53

Brand: CF MOTO Pages: 443

D14/4 BANTAM SUPREME D14/4 BANTAM SPORTS

Brand: BSA Pages: 120

Brand: BOXER Pages: 11

Brand: RDMOTO Pages: 2

KAWASAKI ZX6R 2007/8

Brand: Evotech Performance Pages: 2

TRACER MTT9K 2019

Brand: Yamaha Pages: 122

TT-R125(N) 2000

Brand: Yamaha Pages: 508

TT-R125(R) 2002

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 610

TT-R125(S) 2003

Brand: Yamaha Pages: 610

Brand: Yamaha Pages: 616

Brand: Yamaha Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands