Yamaha Star XV19MY Owner'S Manual Download | Manualshive

Page: 59 / 94

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-17

7

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22430

Front brake pads

Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear

indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 0.8 mm (0.03 in),
have a Yamaha dealer replace the
brake pads as a set.

EAU38630

Checking the brake and clutch
fluid levels

Front brake

Rear brake

1. Brake pad wear indicator groove

1. Lining thickness

1. Minimum level mark

1. Minimum level mark

U1D713E0.book Page 17 Thursday, May 8, 2008 4:19 PM

«
...
57
58
59
60
61
...
»

Summary of Contents for Star XV19MY































































































Reviews:

No comments

Related manuals for Star XV19MY

Brand: Yamaha Pages: 32

Brand: hepco & becker Pages: 4

Brand: klicbag Pages: 2

Brand: NEO TOOLS Pages: 8

990D0-31J50-CLE

Brand: Suzuki Pages: 12

Brand: Dakota Digital Pages: 11

V125 Special 2018

Brand: Lambretta Pages: 53

Multistrada 620

Brand: Ducati Pages: 382

Brand: hepco & becker Pages: 3

STAR XV19CSX(C)

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 100

Star XV250B 2011

Brand: Yamaha Pages: 98

Brand: KTM Pages: 20

Brand: HealTech Electronics Pages: 2

Brand: Healtech Pages: 6

BLITZ 9-13 Visor

Brand: Fubag Pages: 17

Brand: Wunderlich Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands