Yamaha RS90MSL Owner'S Manual Download Page 30 | Manualshive

Page: 30 / 91

background image

5-11

ESU04080

Carburetor coolant shut-off lever

The carburetor coolant shut-off lever controls the flow of
coolant through the carburetor.
Make sure that the lever is in the “ON” position to allow
the coolant to flow and warm the carburetor while the
ambient temperature is below 0 °C (32 °F).

1

Carburetor coolant shut-off lever

2

“ON” (open)

3

“OFF” (closed)

CAUTION:

@

When operating the snowmobile in temperatures
above 0 °C (32 °F), move the carburetor coolant shut-
off lever to the “OFF” position to stop the flow of
coolant, since the carburetor does not need to be
warmed.

@

ESU02421

Storage compartment

Open the storage compartment to store the tool kit,
spare parts, or other small items.

ESU05020

Rear carrier

The rear carrier is located at the rear of the snowmobile.

1

Rear carrier

WARNING

@

Do not use the rear carrier to lift the snowmobile.
The snowmobile could fall, which could result in
severe injury or death.

@

Maximum load limit: 10 kg (22 lb)

U8GE10.book Page 11 Wednesday, June 15, 2005 9:07 AM

«
...
28
29
30
31
32
...
»

Summary of Contents for RS90MSL




























































































Reviews:

No comments

Related manuals for RS90MSL

Brand: Baja motorsports Pages: 15

Sportsman 9921796

Brand: Polaris Pages: 192

Brand: Nakayama Pages: 14

Standard Pedal-Kart

Brand: DINO CARS Pages: 4

Brand: YTL Pages: 14

Brand: Fort Pages: 88

Brand: PRONAR Pages: 121

Pendpac WITTKE RETRO FL

Brand: Labrie Pages: 130

Brand: Baja motorsports Pages: 8

Brand: Yamaha Pages: 172

Brand: Landa Pages: 38

Brand: Landa Pages: 101

Brand: Hammerhead Pages: 55

Expediter EX-21 2017

Brand: Columbia Pages: 32

Brand: BOMBARDIER Pages: 44

Brand: Schmeiser Pages: 28

Brand: Sno Jet Pages: 63

Brand: Storti Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands