Yamaha RS90MSL Owner'S Manual Download Page 29

Page: 29 / 91

5-10

ESU00481

Shroud latches

To open the shroud, unhook the shroud latches, and then
slowly raise the shroud forward until it stops. When clos-
ing the shroud, slowly lower it to its home position, and
then hook the shroud latches.

Shroud latch

Shroud

CAUTION:

Make sure that all cables and wires are in place when
closing the shroud.

WARNING

●

Do not drive the snowmobile with the shroud
open, unlatched, or removed.

●

Keep your body and clothing away from rotating
parts when servicing with the shroud open.

●

Do not touch the hot muffler and engine during or
immediately after operation.

ESU00521

Drive guard

The drive guard is designed to cover the V-belt clutch
and V-belt in case parts break or come loose.

WARNING

●

Make sure that the drive guard is tightened
securely before operating the snowmobile.

●

Never run the engine with the V-belt or drive
guard removed.

ESU00053

V-belt holders

Keep a spare V-belt for emergency use by placing it into
the V-belt holders provided.

CAUTION:

Make sure that the V-belt is installed securely in the
holders.

U8GE10.book Page 10 Wednesday, June 15, 2005 9:07 AM

Summary of Contents for RS90MSL




























































































Search results

Summary of Contents for RS90MSL

Reviews:

Related manuals for RS90MSL

Brands by name

Popular brands

Yamaha RS90MSL, Owner'S Manual

Search results

Summary of Contents for RS90MSL

Reviews:

Related manuals for RS90MSL

Brands by name

Popular brands