Yamaha RS90MSL Owner'S Manual Download Page 32

Page: 32 / 91

6-2

CAUTION:

●

Oxygenated fuels (gasohol) containing a maxi-
mum 5% of ethanol can be used, although richer
jetting may be required to prevent engine dam-
age. Consult a Yamaha dealer. Gasohol contain-
ing methanol is not recommended.

●

Make sure that snow or ice does not enter the fuel
tank when refueling.

●

Do not use alcohol deicers or water absorbing
additives with oxygenated fuel.

●

The fuel tank should be filled with straight gaso-
line as specified.

ESU04031

Engine oil

Use a combination of the recommended SAE and API oil
classifications shown in the chart below.

CB-02E

CAUTION:

Use only 4-stroke engine oil.

SAE

API

SE, SF, SG

higher

-40˚

-20˚

0˚

20˚

40˚

60˚ F

SAE 0W-30

-40˚

-29˚

-18˚

-7˚

4˚

16˚ C

U8GE10.book Page 2 Wednesday, June 15, 2005 9:07 AM

Summary of Contents for RS90MSL




























































































Search results

Summary of Contents for RS90MSL

Reviews:

Related manuals for RS90MSL

Brands by name

Popular brands

Yamaha RS90MSL, Owner'S Manual

Search results

Summary of Contents for RS90MSL

Reviews:

Related manuals for RS90MSL

Brands by name

Popular brands