manualshive.com logo in svg

Yamaha RS90MSL, Owner'S Manual

Share
Download
Yamaha RS90MSL Owner'S Manual Download Page 49

7-8

ESU00245 

Strap

The strap 

1

 should be used only by experienced opera-

tors to assist them when traverse (side-hill) riding.

WARNING

@ 

Improper use of the strap on the handlebar can
result in severe injury or death. 

●

Use the strap only as an operator grip point when
needed to shift weight uphill to maintain balance
during traverse (side-hill) riding. Only experi-
enced operators should traverse slopes steep
enough to require strap use. 

●

Keep the right hand on the right handlebar grip
for steering, and grip the strap with the left hand
to shift weight uphill for balance during traverse
riding. 

●

Ride cautiously while using the strap. Do not
accelerate or decelerate abruptly while holding
onto the strap. 

●

Do not use the strap to lift the snowmobile. 

●

Do not use the strap as a mounting point for
cargo or accessories. 

@

ESU01300 

Driving

WARNING

@ 

Be sure to read the “SAFETY INFORMATION” and
“Riding your snowmobile” sections carefully before
operating the snowmobile. 

@

NOTE:

@ 

Make sure that the engine is warmed up enough before
riding. 

@

1. Release the parking brake by moving the parking

brake lever to the right. 

2. Press the throttle lever slowly to move the snowmo-

bile. 

3. Turn the handlebar in the desired direction. 
4. Squeeze the brake lever to stop the snowmobile. 
5. Apply the parking brake by moving the parking brake

lever to the left. 

U8GE10.book  Page 8  Wednesday, June 15, 2005  9:07 AM

Summary of Contents for RS90MSL




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands