manualshive.com logo in svg

Yamaha RS90L, Owner'S Manual

Share
Download
Yamaha RS90L Owner'S Manual Download Page 71

8-23

ESU02921 

Adjusting the control rods

The weight transfer can be adjusted at the control rods.
The following procedure applies to both control rods.

1. Loosen the locknut 

2

 while holding the control rod

adjusting nut 

1

.

2. To increase weight transfer, turn the adjusting nut in

direction 

a

. To decrease weight transfer, turn the

adjusting nut in direction 

b

.

3. Tighten the locknut. 

CAUTION:

@ 

●

When using the two 22-mm wrenches included in the
tool kit, make sure that they are situated at a right
angle to the control rod as shown, and that they are
tightly fitted to the locknut and the control rod adjust-
ing nut.

●

The adjusting nut of the left and right control rods
must be set to the same position. Uneven settings
can cause poor handling and loss of stability. 

@

WARNING

@ 

Never adjust the control rods beyond the maximum
range indicated on the rods with red paint 

3

. 

@

c

Adjustable range 

d

Standard position 

Locknut tightening torque: 

25 Nm (2.5 m·kgf, 18 ft·lb)

E_8es.book  Page 23  Saturday, August 6, 2005  8:47 AM

Summary of Contents for RS90L





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands