manualshive.com logo in svg

Yamaha RS90L, Owner'S Manual

Share
Download
Yamaha RS90L Owner'S Manual Download Page 55

8-7

ESU03701 

Adjusting the engine idling speed

CAUTION:

@ 

●

Be sure to have a Yamaha dealer make this
adjustment. 

●

Make sure that the throttle lever moves smoothly. 

●

Make sure that the carburetor is synchronized
first. 

@

1. Start the engine and warm it up.

NOTE:

@ 

Refer to the “Starting the engine” section. 

@

2. Turn the throttle stop screw 

1

 in or out to adjust the

engine idle speed.

ESU01472 

Adjusting the throttle cable

CAUTION:

@ 

Be sure to adjust the engine idle speed first. 

@

1. Loosen the locknut.
2. Turn the adjuster in or out until the proper throttle

lever free play is achieved.

1

Locknut 

2

Adjuster

3. Tighten the locknut. 

ESU04870 

Adjusting the carburetors

The carburetors are an important part of the engine and
its emission control system, which require very sophisti-
cated adjustment. Therefore, carburetor adjustments
should be left to a Yamaha dealer, who has the neces-
sary professional knowledge and experience. 

Standard engine idle speed: 1,400 

±

 100 r/min 

Throttle lever free play 

a

: 

2.0–3.0 mm (0.08–0.12 in)

E_8es.book  Page 7  Saturday, August 6, 2005  8:47 AM

Summary of Contents for RS90L





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands