Yamaha RS90L Owner'S Manual Download Page 38

Page: 38 / 92

6-9

ESU01020

Skis and ski runners

Check the skis and ski runners for wear and damage.
Replace if necessary.

CAUTION:

Avoid scratching the skis when loading and unload-
ing the snowmobile, when riding in areas with little
or no snow, or on sharp edges such as concrete,
curbs, etc. This will wear or damage the skis.

ESU00103

Steering system

Check the handlebar for excessive free play:

1. Push the handlebar up and down and back and forth.
2. Turn the handlebar slightly to the right and left.

If excessive free play is noticed, consult a Yamaha
dealer.

ESU00378

Lights

Check the lights.
Replace any burned out bulbs.

CAUTION:

Avoid using a scraper or hot water for cleaning the
plastic lenses

Ski runner wear limit

8 mm (0.31 in)

Ski wear limit

12 mm (0.47 in)

E_8es.book Page 9 Saturday, August 6, 2005 8:47 AM

Summary of Contents for RS90L





























































































Search results

Summary of Contents for RS90L

Reviews:

Related manuals for RS90L

Brands by name

Popular brands

Yamaha RS90L, Owner'S Manual

Search results

Summary of Contents for RS90L

Reviews:

Related manuals for RS90L

Brands by name

Popular brands