Yamaha RS90L Owner'S Manual Download Page 68

Page: 68 / 92

8-20

ESU02372

Adjusting the ski spring preload

The spring preload can be adjusted by turning the spring
preload adjuster

CD-11E

CAUTION:

The left and right ski spring preload must be set to
the same setting. Uneven settings can cause poor
handling and loss of stability.

WARNING

This shock absorber contains highly pressurized
nitrogen gas. It could explode by improper handling,
causing injury, or property damage.

●

Do not tamper with or attempt to open the shock
absorber.

●

Do not subject the shock absorber to an open
flame or other high heat source, which could
cause it to explode.

●

Do not deform or damage the shock absorber in
any way.

●

Do not dispose of a worn or damaged shock
absorber by yourself. Take the unit to a Yamaha
dealer.

Spring seat length*

Standard

Increased

←

→

Decreased

Preload

Harder

←

→

Softer

Length

Maximum
172.0 mm
(6.77 in)

162.0 mm

(6.38 in)

Minimum
155.5 mm
(6.12 in)

∗

The spring seat length changes approximately 1.5 mm (0.06 in) with
each full turn of the adjuster.

E_8es.book Page 20 Saturday, August 6, 2005 8:47 AM

Summary of Contents for RS90L





























































































Search results

Summary of Contents for RS90L

Reviews:

Related manuals for RS90L

Brands by name

Popular brands

Yamaha RS90L, Owner'S Manual

Search results

Summary of Contents for RS90L

Reviews:

Related manuals for RS90L

Brands by name

Popular brands