Yamaha Helm Master Operation Manual Download Page 5

Page: 5 / 52

Table of contents

Alert message information .............. 1

Alert Notifications ............................ 1
Other Notifications ........................... 4

General information ......................... 5

List of abbreviations ........................ 5
Read labels and related
manuals ........................................... 5
Warning and caution labels ............. 6

Function and operation of
components ...................................... 9

EKS ............................................... 10

EKS fob ............................................ 10
Ignition switch ................................... 11
Start/stop switch ............................... 11
All ignition switch
(for triple engine application) ............ 11
All start/stop switch
(for triple engine application) ............ 11

Engine shut-off switch ................... 11
Remote control box ....................... 12

Remote control lever  ........................ 13
Lever friction adjuster  ....................... 16
Free throttle switch  ........................... 16
Single lever switch ............................ 16
Center engine switch
(for triple engine application) ............ 17
Speed control switch  ........................ 17
Station selector switch
(for dual station)  ............................... 18
Trim assist switch  ............................. 19
Power Trim and Tilt (PTT) switch  ..... 19
Remote control active indicator  ........ 20
Remote control alert indicator .......... 21

Joystick control .............................. 22

Joystick lever .................................... 22
Joystick switch .................................. 24
High mode switch ............................. 24

Digital Network Gauge (6Y9) ........ 25

Steering friction ................................ 26
Rudder angle .................................... 26

Pre-operation checks .................... 35

Temporary actions in
emergency ...................................... 37

Steering malfunction ..................... 37

One engine’s steering does not
operate (locked or free) .................... 37
All engine’s steering do not
operate ............................................. 38
Engine interference protection ......... 39
When the steering response
becomes slow ................................... 41

Periodic maintenance .................... 42

Maintenance table ......................... 42
Recommended hydraulic fluid ....... 44

Transportation with boat
(trailering) ....................................... 45

0KAW_dtp_data_US.book Page 1 Monday, December 17, 2012 3:35 PM

Summary of Contents for Helm Master





















































Search results

Summary of Contents for Helm Master

Reviews:

Related manuals for Helm Master

Brands by name

Popular brands

Yamaha Helm Master, Operation Manual

Search results

Summary of Contents for Helm Master

Reviews:

Related manuals for Helm Master

Brands by name

Popular brands