Yamaha Helm Master Operation Manual Download Page 15 | Manualshive

Page: 15 / 52

background image

10

Function and operation of components

EKS

The EKS consists of the EKS panel and the
EKS fob. EKS functions: EKS locking/un-
locking using EKS fob, ignition ON/OFF and
engine starting and stopping.
The EKS panel for triple engine installations
is equipped with an All ignition switch and an
All start/stop switch. Pressing the All ignition
switch will provide power for all engines.
Pressing the All start/stop switch will start or
stop all engines.

1. EKS fob (2 pcs)
2. Active indicator
3. Ignition switch (PORT)
4. Ignition switch (STBD)
5. Start/stop switch (PORT)
6. Start/stop switch (STBD)
7. Lock indicator
8. Ignition switch (Center)
9. Start/stop switch (Center)
10. All ignition switch

11. All start/stop switch

A. Twin engine application
B. Triple engine application

■

EKS fob

Place and hold the EKS fob over the lock in-
dicator in EKS panel to lock and unlock the
EKS.

TIP:

• Be sure to lock the EKS when leaving the

boat, or when leaving the operator’s seat if
children are nearby. Also, check that the
lock indicator is blinking.

• Repeated operation of the EKS fob lock/

unlock function may result in improper
operation. Be sure to operate the EKS fob
in at least 1-second intervals.

• When locking/unlocking with the EKS fob,

do not place the key close to devices pos-
sessing a magnetic field, as this may pre-
vent the lock/unlock operation.

• The EKS will allow to register up to four

EKS fobs. Have a Yamaha dealer register
any additional EKS fobs.

• When operating or stopping the boat, be

sure to carry the EKS fob with you and
take care not to lose it.

• If any EKS fob is lost, be sure to have a

Yamaha dealer delete the registration of
the lost key number for security reasons.

• While operating the ignition switch or

engine start switch, do not turn the steer-
ing wheel or perform any system opera-
tions at the same time, otherwise
unexpected errors may occur.

IGNITION

IGNITION

START

STOP

START

STOP

A

1

7

4

3

2

6

5

IGNITION

IGNITION

START

STOP

START

STOP

IGNITION

IGNITION

CENTER

STBD

ALL

PORT

START

STOP

START

STOP

B

3

10

8

5

4

6

2

11

9

7

7

0KAW_dtp_data_US.book Page 10 Monday, December 17, 2012 3:35 PM

«
...
13
14
15
16
17
...
»

Summary of Contents for Helm Master





















































Reviews:

No comments

Related manuals for Helm Master

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: DANLERS Pages: 2

Brand: Haas Automation Pages: 26

Growers Supply 109722

Brand: FarmTek Pages: 9

Brand: IDEAL Pages: 12

Brand: IDEAL Networks Pages: 60

Brand: IceCure Pages: 104

Brand: VanGaa Lighting Pages: 7

GPSMAP 7400 Series

Brand: Garmin Pages: 8

Brand: K-SPORT Pages: 5

Brand: ProLights Pages: 28

DeviceNet CompactPCI 1784-CPCIDS

Brand: Allen-Bradley Pages: 36

Brand: Exmark Pages: 36

Brand: Manley Pages: 18

Brand: Gardenline Pages: 24

Brand: Analogue Solutions Pages: 64

Power System KPS-US

Brand: Keys Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands