Yamaha GP1300R WaveRunner 2008 Owner'S/Operator'S Manual Download Page 7

Page: 7 / 98

General and important labels

EJU30340

Emission control information

This engine conforms to 2008 U.S. Environ-
mental Protection Agency (EPA) regulations
for marine SI engines.

EJU30380

Approval label of emission control
certificate

This label is attached to the electrical box and
the intake side of the crankcase.

New Technology; Catalytic converter

EJU30420

Manufactured date label

This label is attached to the electrical box and
the intake side of the crankcase.

Emission control information label location

Manufactured date label location

UF1G15E0.book Page 2 Thursday, May 31, 2007 9:09 AM

Summary of Contents for GP1300R WaveRunner 2008



































































































Search results

Summary of Contents for GP1300R WaveRunner 2008

Reviews:

Related manuals for GP1300R WaveRunner 2008

Brands by name

Popular brands

Yamaha GP1300R WaveRunner 2008, Owner'S/Operator'S Manual

Search results

Summary of Contents for GP1300R WaveRunner 2008

Reviews:

Related manuals for GP1300R WaveRunner 2008

Brands by name

Popular brands