Yamaha GP1300R WaveRunner 2008 Owner'S/Operator'S Manual Download Page 43

Page: 43 / 98

Features and functions

engine warning indicator begin to blink, and
the buzzer sounds intermittently.

If this occurs, reduce the engine speed, return
to shore, and have a Yamaha dealer check
the engine.

EJU31680

Storage compartments

A front storage compartment and a glove
compartment are provided.

NOTE:

●

Make sure that the storage compartments
are securely closed before operating the
watercraft.

●

The storage compartments are not de-
signed to be waterproof. If you carry objects
that must be kept dry, such as the manuals,
put them in a waterproof bag.

EJU31701

Front storage compartment

The front storage compartment is located at
the bow.

To open the front storage compartment, push
the hood latch down, and then lift up the hood.

Hood latch

Front storage compartment

Front storage compartment:

Capacity:

16.0 L (4.2 US gal) (3.5 Imp.gal)

Load limit:

5.0 kg (11 lb)

UF1G15E0.book Page 38 Thursday, May 31, 2007 9:09 AM

Summary of Contents for GP1300R WaveRunner 2008



































































































Search results

Summary of Contents for GP1300R WaveRunner 2008

Reviews:

Related manuals for GP1300R WaveRunner 2008

Brands by name

Popular brands

Yamaha GP1300R WaveRunner 2008, Owner'S/Operator'S Manual

Search results

Summary of Contents for GP1300R WaveRunner 2008

Reviews:

Related manuals for GP1300R WaveRunner 2008

Brands by name

Popular brands