Yamaha FL350A Page 89 Owner'S Manual Download

Page: 89 / 122

Operation

4. Once the outboard motor is supported

with the tilt support lever, press the pow-
er trim and tilt switch “

” (down) to re-

tract the trim rods.

NOTICE:

Make sure

that the trim rods retracts completely
during mooring. This protects the
rods from marine growth and corro-
sion, which could damage the power
trim and tilt mechanism.

[ECM00252]

EMU35515

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2. Release the tilt support lever.

3. Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

ZMU05824

ZMU05856

ZMU06258

ZMU05840

6AW-9-77-1E0.book 82 ページ２０１０年３月１６日　火曜日　午後６時８分

Summary of Contents for FL350A



























































































































Search results

Summary of Contents for FL350A

Reviews:

Related manuals for FL350A

Brands by name

Popular brands

Yamaha FL350A, Owner'S Manual

Search results

Summary of Contents for FL350A

Reviews:

Related manuals for FL350A

Brands by name

Popular brands