Yamaha FL350A Owner'S Manual Download

Page: 120 / 122

Trouble Recovery

113

5. Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01950]

6. Remove the bolts to remove the cover.

7. Unscrew the filter cup from the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01960]

8. Drain the water in the filter cup by soak-

ing it up with a rag.

9. Firmly screw the filter cup onto the filter

housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01970]

10. Install the cover, and tighten the bolts.

1. Water detection switch coupler

ZMU05892

ZMU05894

1. Filter cup
2. Water detection switch lead

ZMU05895

ZMU05896

6AW-9-77-1E0.book 113 ページ２０１０年３月１６日　火曜日　午後６時８分

Summary of Contents for FL350A



























































































































Search results

Summary of Contents for FL350A

Reviews:

Related manuals for FL350A

Brands by name

Popular brands

Yamaha FL350A, Owner'S Manual

Search results

Summary of Contents for FL350A

Reviews:

Related manuals for FL350A

Brands by name

Popular brands