manualshive.com logo in svg

Yamaha FL350A, Owner'S Manual

Share
Download
Yamaha FL350A Owner'S Manual Download Page 73

Operation

66

side control lever.

●

The center engine runs at the average
speed of port side and starboard side en-
gines’ speeds.

●

Operate the starboard side engine using
the starboard side control lever.

2. Push the engine selector switch once to

operate the port side and starboard side
engines.

●

Operate the port side engine using the port
side control lever.

●

The center engine runs at the idling speed.

●

Operate the starboard side engine using
the starboard side control lever.

3. Push the engine selector switch twice to

operate the center engine.

●

The port side engine runs at the idling
speed.

●

Operate the center engine using the port
side control lever.

●

The starboard side engine runs at the
idling speed.

4. Push the engine selector switch three

times to operate the three engines.

ZMU06000

ZMU06001

ZMU06000

ZMU06002

ZMU06000

6AW-9-77-1E0.book  66 ページ  ２０１０年３月１６日　火曜日　午後６時８分

Summary of Contents for FL350A



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands