manualshive.com logo in svg

Yamaha FL350A, Owner'S Manual

Share
Download
Yamaha FL350A Owner'S Manual Download Page 50

Instruments and indicators

43

EMU36221

Overheat alert

If the engine temperature rises too high while
cruising, the overheat-alert indicator will start
to blink. The engine speed will automatically
decrease to about 2000 r/min.

Stop the engine immediately if the buzzer
sounds and the overheat alert device has ac-
tivated. Check the cooling water inlet for
clogging.

NOTICE

ECM01592

●

Do not continue to run the engine if the
overheat-alert indicator blinks. Serious
engine damage will occur.

●

Do not continue to operate the engine if
a alert device has activated. Consult
your Yamaha dealer if the problem can-
not be located and corrected.

EMU36150

Water separator alert

This indicator will blink if water has accumu-
lated in the water separator (fuel filter) while
cruising. In such an event, stop the engine
immediately and see page 110 of this manu-
al to drain the water from the fuel filter. Get
back to the port soon and consult a Yamaha
dealer immediately.

NOTICE

ECM00910

Gasoline mixed with water could cause
damage to the engine.

EMU36160

Engine trouble alert

This indicator will blink if the engine malfunc-
tions while cruising. Get back to the port
soon and consult a Yamaha dealer immedi-
ately.

NOTICE

ECM00920

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer im-
mediately.

EMU36170

Low battery voltage-alert

If the battery voltage drops, the low battery
voltage-alert indicator and the battery volt-
age value will start to blink. Get back to the

ZMU05421

ZMU05423

ZMU05425

6AW-9-77-1E0.book  43 ページ  ２０１０年３月１６日　火曜日　午後６時８分

Summary of Contents for FL350A



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands