Yamaha FL250G Owner'S Manual Download Page 56

Page: 56 / 86

Operation

EMU42700

Procedure for tilting down (power trim
and tilt models)

Push the power trim and tilt switch “

”

(up) until the outboard motor is supported
by the tilt rod and the tilt support lever be-
comes free.

Release the tilt support lever.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to the
desired position.

EMU28062

Shallow water

EMU32871

Power trim and tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM01490

●

If the engine speed is suddenly in-
creased when the outboard motor is par-
tially tilted up, the power trim and tilt unit
could be damaged.

●

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit
is above the surface of the water when
setting up for and cruising in shallow
water. Otherwise severe damage from
overheating can result.

EMU32922

Procedure for power trim and tilt models

Place the remote control lever in neutral.

ZMU07546

ZMU04196

ZMU04603

ZMU04588

U6DXK0E0.book Page 50 Friday, May 13, 2011 3:08 PM

Summary of Contents for FL250G























































































Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands

Yamaha FL250G, Owner'S Manual

Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands