Yamaha FL250G Owner'S Manual Download Page 45

Page: 45 / 86

Operation

nected, cooling water can leak out and the
engine can overheat during operation.

[ECM01801]

EMU36941

Install cowling

Be sure that all cowling lock levers are re-
leased.

Be sure that the rubber seal is seated all
the way around the engine.

Place the cowling on top of the seal.

Check to be sure it fits properly in the rub-
ber seal.

Move the levers to lock the cowling as
shown.

NOTICE:

If the top cowling is

not installed correctly, water spray un-
der the top cowling can damage the
engine, or the top cowling can blow off
at high speeds.

[ECM01991]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

1. Fitting

2. Flushing device

ZMU06164

ZMU06131

ZMU06133

U6DXK0E0.book Page 39 Friday, May 13, 2011 3:08 PM

Summary of Contents for FL250G























































































Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands

Yamaha FL250G, Owner'S Manual

Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands