Yamaha FL250G Owner'S Manual Download Page 4

Page: 4 / 86

Table of contents

Safety information............................. 1

Outboard motor safety .................... 1

Boating safety ................................. 2

General information .......................... 4

Identification numbers record .......... 4

Outboard motor serial number ........... 4
Key number ........................................ 4

Read manuals and labels................ 5

Warning labels.................................... 5

Specifications and requirements..... 8

Specifications .................................. 8
Installation requirements ................. 9

Boat horsepower rating ...................... 9
Mounting motor .................................. 9

Remote control requirements .......... 9
Battery requirements ..................... 10

Battery specifications .......................  10
Mounting battery...............................  10
Multiple batteries ..............................  10

Propeller selection......................... 10

Counter rotation models ................... 10

Start-in-gear protection .................  11
Engine oil requirements ................  11
Fuel requirements .........................  11

Gasoline ........................................... 11

Muddy or acidic water ...................  12
Anti-fouling paint ...........................  12
Motor disposal requirements.........  12
Emergency equipment ..................  12

Components .................................... 13

Components diagram.................... 13

Remote control box ..........................  14
Remote control lever ........................  15
Free accelerator ...............................  15
Throttle friction adjuster ....................  16
Engine shut-off cord (lanyard) and

clip................................................. 16

Main switch....................................... 17
Power trim and tilt switch on remote

control ........................................... 17

Power trim and tilt switch on bottom

cowling .......................................... 17

Power trim and tilt switches

(twin binnacle type) ....................... 18

Trim tab with anode .......................... 18
Tilt support lever for power trim and

tilt model........................................ 19

Cowling lock lever (pull up type).......  19
Flushing device ................................  20
Fuel filter/Water separator ................  20

Instruments and indicators............ 22

Digital tachometer ......................... 22

Tachometer ......................................  22
Trim meter ........................................  22
Hour meter .......................................  22
Low oil pressure-alert indicator ........  23
Overheat-alert indicator ....................  23

Digital speedometer ...................... 23

Speedometer ....................................  23
Fuel gauge .......................................  24
Trip meter / Clock / Voltmeter...........  24
Fuel level-alert indicator ...................  25
Low battery voltage-alert indicator ...  25

Fuel management meter............... 25

Fuel flow meter ................................. 25

U6DXK0E0.book Page 1 Friday, May 13, 2011 3:08 PM

Summary of Contents for FL250G























































































Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands

Yamaha FL250G, Owner'S Manual

Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands