Yamaha FL250G Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 86

background image

Specifications and requirements

11

propeller with a counter rotation motor, or
a counter rotation propeller with a stan-
dard motor. Otherwise the boat could go
in the direction opposite of that expected
(for example, reverse instead of forward),
which could lead to an accident.

[EWM01810]

For instructions on propeller removal and in-
stallation, see page 65 and 65.

EMU25770

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped with
start-in-gear protection device(s). This feature
permits the engine to be started only when it
is in neutral. Always select neutral before
starting the engine.

EMU41951

Engine oil requirements

Select an oil grade according to the average
temperatures in the area where the outboard
motor will be used.

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an al-
ternative oil grade listed under
Recommended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36360

Fuel requirements

EMU43940

Gasoline

Use a good quality gasoline. If knocking or
pinging occurs, use a different brand of gaso-
line or premium unleaded fuel.

NOTICE

ECM01981

●

Do not use leaded gasoline. Leaded gas-
oline can seriously damage the engine.

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL

Total engine oil quantity (oil pan capaci-
ty):

5.6 L (5.92 US qt, 4.93 Imp.qt)

Replacement engine oil quantity (at peri-
odic maintenance):

Without oil filter replacement:

4.5 L (4.76 US qt, 3.96 Imp.qt)

With oil filter replacement:

4.7 L (4.97 US qt, 4.14 Imp.qt)

Recommended gasoline:

Regular unleaded gasoline with a
minimum octane rating of 90 (Re-
search Octane Number).

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

U6DXK0E0.book Page 11 Friday, May 13, 2011 3:08 PM

«
...
15
16
17
18
19
...
»

Summary of Contents for FL250G























































































Reviews:

No comments

Related manuals for FL250G

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 64

Brand: Data I/O Pages: 175

Brand: Sun Microsystems Pages: 74

Brand: Gigabyte Pages: 40

TLV320AIC3111 EVM

Brand: Texas Instruments Pages: 39

Brand: Analog Devices Pages: 24

Brand: Gigabyte Pages: 36

Brand: IEI Technology Pages: 15

Brand: JETWAY Pages: 49

Brand: BESTEK Pages: 47

Linear DC2681A-A

Brand: Analog Devices Pages: 8

Brand: ECS Pages: 74

Brand: Supero Pages: 78

Brand: PCchips Pages: 42

Brand: MSI Pages: 104

Brand: DFI Pages: 48

Brand: JETWAY Pages: 45

Brand: Raisonance Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands