Yamaha FL250G Owner'S Manual Download Page 5

Page: 5 / 86

Table of contents

Fuel economy meter / Twin
engine speed synchronizer ........... 26

Water separator-alert indicator......... 28

6Y8 Multifunction meters............... 28
6Y8 Multifunction tachometers ...... 28

Start-up checks ................................  29
Low oil pressure-alert .......................  29
Overheat alert...................................  29
Water separator alert........................  29
Engine trouble alert ..........................  30
Low battery voltage-alert ..................  30

6Y8 Multifunction speed &

fuel meters ................................. 30

6Y8 Multifunction fuel

management meters .................. 31

Engine control system.................... 32

Alert system .................................. 32

Overheat alert................................... 32
Low oil pressure alert ....................... 32

Installation ....................................... 34

Installation ..................................... 34

Mounting the outboard motor ........... 34

Operation ......................................... 36

First-time operation ....................... 36

Fill engine oil ....................................  36
Breaking in engine............................  36
Getting to know your boat ................  36

Checks before starting engine ...... 36

tilt system ...................................... 40

Battery .............................................. 41

Filling fuel...................................... 41
Operating engine .......................... 41

Sending fuel ..................................... 42
Starting engine ................................. 42

Checks after starting engine ......... 43

Cooling water ................................... 43

Warming up engine....................... 44

Electric start models ......................... 44

Checks after engine warm up ....... 44

Shifting ............................................. 44
Stop switches ................................... 44

Shifting ..........................................  44
Stopping boat................................  45
Stopping engine ............................  45

Procedure ......................................... 45

Trimming outboard motor.............. 46

Adjusting trim angle

(Power trim and tilt) ....................... 46

Adjusting boat trim............................ 47

Tilting up and down....................... 48

Procedure for tilting up

(power trim and tilt models)........... 48

Procedure for tilting down

(power trim and tilt models)........... 50

Shallow water................................ 50

Power trim and tilt models ................ 50

Cruising in other conditions........... 51

Maintenance .................................... 52

Transporting and storing outboard

motor.......................................... 52

Storing outboard motor.....................  52
Procedure .........................................  53
Lubrication ........................................  54
Flushing power unit ..........................  54
Cleaning the outboard motor ............  55
Checking painted surface of

outboard motor.............................. 56

Periodic maintenance ................... 56

Replacement parts ...........................  56
Severe operating conditions .............  56
Maintenance chart 1 .........................  57
Maintenance chart 2 .........................  59
Greasing ...........................................  60

U6DXK0E0.book Page 2 Friday, May 13, 2011 3:08 PM

Summary of Contents for FL250G























































































Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands

Yamaha FL250G, Owner'S Manual

Search results

Summary of Contents for FL250G

Reviews:

Related manuals for FL250G

Brands by name

Popular brands