Yamaha FJR1300S(C) Owner'S Manual Download

Page: 75 / 99

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU23900

Replacing a headlight bulb

This model is equipped with quartz bulb
headlights. If a headlight bulb burns
out, replace it as follows.

1. Remove panel B (if replacing the

left headlight bulb) or panel C (if re-
placing the right headlight bulb).
(See page 6-8.)

2. Disconnect the headlight coupler,

and then remove the headlight
bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10650

Take care not to damage the follow-
ing parts:

1. Headlight coupler

2. Headlight bulb cover

1. Headlight bulb holder

5JW11.book Page 33 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands