Yamaha FJR1300S(C) Owner'S Manual Download Page 51

Page: 51 / 99

PERIODIC MAINTENANCE AND MINOR REPAIR

6-9

To install the panel

1. Place the panel in the original posi-

tion, and then tighten the quick fas-
tener screw and install the screws.

2. Install panel A (to complete the in-

stallation of panel B) or panel D (to
complete the installation of panel
C).

EAU19210

Panel D

To remove the panel
Remove the screws, and then take the
panel off.

To install the panel
Place the panel in the original position,
and then install the screws.

EAU19450

Panels E and F

To remove one of the panels

1. Remove the seats. (See page

3-11.)

2. Remove the screws, the quick fas-

tener screw and the quick fasten-
ers, and then take the panel off.

To install the panel

1. Place the panel in the original posi-

tion, and then install the quick fas-
teners and quick fastener screw,
and tighten the screws.

2. Install the seats.

1. Screw
2. Quick fastener

1. Screw

1. Screw
2. Quick fastener screw

3. Quick fastener

5JW11.book Page 9 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands