Yamaha FJR1300S(C) Owner'S Manual Download Page 65 | Manualshive

Page: 65 / 99

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

6

the braking performance, which may
result in loss of control and an acci-
dent.

EAU22270

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22420

Front brake pads

Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

5JW11.book Page 23 Friday, May 9, 2003 4:03 PM

«
...
63
64
65
66
67
...
»

Summary of Contents for FJR1300S(C)




































































































Reviews:

No comments

Related manuals for FJR1300S(C)

Brand: R&G Pages: 8

Brand: KYMCO Pages: 55

Brand: R&G Pages: 8

Brand: Ohlins Pages: 4

Brand: AGV Pages: 64

Pulsar 135 BS VI

Brand: Bajaj Pages: 48

Brand: Dakota Digital Pages: 11

Brand: Suzuki Pages: 165

Brand: Shark Pages: 80

Brand: JIMS Pages: 2

Brand: PUIG Pages: 3

Brand: Honda Pages: 153

CR125M Elsinore

Brand: Honda Pages: 64

Brand: Honda Pages: 202

Brand: Honda Pages: 160

Brand: Honda Pages: 148

CB UNICORN DAZZLER 2010

Brand: Honda Pages: 89

Brand: Honda Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands