Yamaha FJR1300S(C) Owner'S Manual Download Page 49

Page: 49 / 99

PERIODIC MAINTENANCE AND MINOR REPAIR

6-7

NOTE:

From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.

EAU17660

NOTE:

●

The air filter needs more frequent service if you are riding in unusually wet or dusty areas.

●

Hydraulic brake and clutch systems

• After disassembling the brake or clutch master cylinders, caliper cylinders or clutch release cylinder, always change

the fluid. Regularly check the brake and clutch fluid levels and fill the reservoirs as required.

• Replace the oil seals on the inner parts of the brake or clutch master cylinders, caliper cylinders and clutch release

cylinder every two years.

• Replace the brake and clutch hoses every four years or if cracked or damaged.

5JW11.book Page 7 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands